- 您现在的位置：买卖IC网 > Sheet目录338 > LT3754IUH#TRPBF (Linear Technology)IC LED DVR 16CH 50MA 32QFN
LT3754
OPERATION
to define the turn on/off voltages for V IN . SHDN /UVLO pin
current switches from 2.4μA to 0μA when SHDN /UVLO
pin voltage exceeds 1.476V.
The LT3754 constant switching frequency is program-
mable from 100kHz up to 1MHz using a single resistor
at the RT pin to ground. A SYNC pin is also provided to
allow an external clock to define the converter switch-
ing frequency. The GATE output provides a ±0.8A peak
gate drive for an external N-channel power MOSFET to
generate a boosted output voltage V OUT using a single
inductor, Schottky diode and output capacitor. With LED
strings connected from V OUT to every LED pin, the lowest
voltage on each LED pin is monitored and compared to
an internal 1.1V reference. V OUT is regulated to ensure
the lowest LED pin voltage of any connected LED string
is maintained at 1.1V. If any of the LED strings are open,
the LT3754 regulation loop will ignore the open LED pin.
If all of the LED strings are open V OUT charges up until
a user programmable OVP (overvoltage protection) level
is reached. This programmable OVP level allows the user
to protect against LED damage when the LED strings are
opened and then reconnected.
Since the LT3754 boost controller uses a current mode
topology, the V C pin voltage determines the peak current
in the inductor of the converter and hence the duty cycle
of the GATE switching waveform. The basic loop uses a
pulse from an internal oscillator to set an RS flip-flop and
turn on the external power MOSFET. Current increases
in the MOSFET and inductor until the V C commanded
peak switch current is exceeded and the MOSFET is then
turned off. Inductor current is sensed during the GATE on
period by a sense resistor RS in the source of the external
N-channel power MOSFET. As with all current mode
converters, slope compensation is added to the control
path to ensure stability for duty cycles above 50%. Any
over current fault condition in the MOSFET turns off the
MOSFET and triggers soft-start internally. In this fault mode
the LT3754 only allows MOSFET turn-on approximately
every 2ms. This hiccup mode significantly reduces the
power rating required for the MOSFET.
LED current programming and dimming can be achieved
using the I SET , CTRL and PWM pins. A single resistor at
the I SET pin programs LED current. Analog dimming of
LED brightness is achieved using the CTRL pin below 1V.
PWM dimming of LED brightness is achieved by control-
ling the duty cycle of the PWM pin.
For robust operation the LT3754 monitors system
conditions and performs soft-start for start-up after any of
the following faults: V IN , SHDN or INTV CC voltages too low or
MOSFET current too high. The LT3754, when entering these
faults, discharges an internal soft-start node and prevents
switching at the GATE pin. When exiting these faults the
LT3754 ramps up an internal soft-start node to control V C
pin voltage rise and hence control MOSFET peak switch
current rise. In addition the soft-start period gradually
ramps up switching frequency from approximately 33%
to 100% of full scale.
The LT3754 monitors each LED pin voltage. If the LED
string has an open fault (V(LED X )<0.5V) the FAULT flag
is pulled low.
For LED protection, the LT3754 CTRL pin allows an LED
current derating curve to be programmed versus the
ambient temperature of the LED strings. An NTC resistor
placed close to the LEDs decreases CTRL pin voltage and
hence decreases LED current as LED ambient temperature
increases.
The LT3754 also allows its own junction temperature to
be monitored and regulated by derating LED currents
when a junction temperature programmed by the T SET
pin is exceeded.
3754fc
10
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LT3755EMSE#PBF
IC LED DRVR HP CONS CURR 16-MSOP
LT3760EFE#PBF
IC LED DVR WHT/CLR BCKLT 28TSSOP
LT3799IMSE#PBF
IC LED DRIVER TRIAC DIM 16-MSOP
LT3956EUHE#PBF
IC LED DVR BUCK BOOST 36-VQFN
LTC3201EMS#TRPBF
IC LED DRVR WHITE BCKLGT 10-MSOP
LTC3202EDD#PBF
IC LED DRIVR WHITE BCKLGT 10-DFN
LTC3205EUF#TRPBF
IC LED DRVR WT/RGB BCKLGT 24-QFN
LTC3206EUF#TRPBF
IC LED DRVR WT/RGB BCKLGT 24-QFN
相关代理商/技术参数
LT3754IUHPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver
LT3754IUHTRPBF
制造商:LINER 制造商全称:Linear Technology 功能描述:16-Channel × 50mA LED Driver
LT3755
制造商:LINER 制造商全称:Linear Technology 功能描述:60V 4-Switch Synchronous
LT3755-1
制造商:LINER 制造商全称:Linear Technology 功能描述:60V 4-Switch Synchronous
LT3755-2
制造商:LINER 制造商全称:Linear Technology 功能描述:60V 4-Switch Synchronous
LT3755EMSE#PBF
功能描述:IC LED DRVR HP CONS CURR 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C
LT3755EMSE#PBF
制造商:Linear Technology 功能描述:DRIVER LED 40VIN 1MHZ 16MSOP 制造商:Linear Technology 功能描述:DRIVER, LED, 40VIN, 1MHZ, 16MSOP
LT3755EMSE#TRPBF
功能描述:IC LED DRVR HP CONS CURR 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND